INDUSTRIAL WASTE BURNING
Industrial waste incinerators also have many other names such as: Industrial incinerators, Industrial waste incineration systems, Industrial incineration systems, Industrial waste incinerators, Industrial waste incinerators , Industrial waste treatment systems, Industrial waste treatment systems, etc. Distribution representatives of Japan always bring customers advanced waste treatment systems and high quality.
The hazardous industrial waste incinerator is designed to burn certain types of industrial waste such as: plastic packaging, rubber, cloth, cotton wool, rags, wood grain, sludge, mineral oil, lubricating grease. industry, ... According to the analysis, the average level of their components are in the following range:
- Composition of rags: 43%; Composition of rag: 12%
- Plastic composition: 42%; Rubber component: 1%
- Composition of sediment: ~ 2%
The chemical composition of wastes is usually in the following range.
Note: "-" is unknown.
The calorific value of garbage is about ~ 5,000 kcal / kg.
2. Main specifications of the line
- Product code: PO-LDR5.
- Productivity: 100-500 kg / hr.
- Electricity consumption: 50 kWh / ton of garbage.
- Fuel consumption: 50-100 liters of DO oil / ton (rubbish with calorific value> 2500 kca / kg) and 100-250 liter / ton with flammable waste (mud, chemicals, etc. with calorific value <1000 kcal / kg).
- Main equipment: The unit that receives and supplies waste into the furnace, incinerator, gas cooling system, exhaust treatment system, gas treatment tank system, chimney, electrical equipment, piping system gas, water treatment systems, control systems ...
3. Specifications of main equipment in the line
3.1. Parts receiving and feeding waste into the furnace
Automatic or manual control:
- Dumping tanks: 01, CT3 material; Capacity: 0.1m3; Lifting height: 3m
- Frequency feeders: 10 times / h; Useful capacity: 0.15m3; Drive method: Hydraulic
- Combustion chamber: Burning 2 primary and secondary chambers
- Materials: Samot bricks, light bricks, asbestos sheets, 4mm thick corrugated iron sheets, shaped steel furnace frames.
- Dimensions: LxWxH: 4700 x 3000 x 5600
- Automatic mixing and recording system: Hydraulic control
- Working floor: Sandpaper floor surface
– Lan can: Tổ hợp;
- 2 sets of oil burners, which are used for either of the following two types:
- Burners usually: Origin: G7 devices; Fuel: DO oil
- Pressure burner: Origin: Vietnam; Fuel: DO oil; Automatic valve: 2 sets
- 8at air compressor: 1 set; Product area 8at, 1m3: 1 set
- Oil tank: Material: CT3, Capacity: 1m3; Oil supply pump: 01 piece
3.3. Air cooling system
- Water cooled set: 01 set; Type: tubular heat exchanger; Fabricated materials: Heat resistant steel
- Heat recovery unit of exhaust fumes: 01 set; Type: tubular heat exchanger; Fabricated materials: Heat resistant steel.
- Blower: 01 unit; Type: industrial fan; Capacity: 5000 m3 / h; Electric motor: 5 kW.
- Water supply pumps: 01 unit; Type: G7 device; Productivity: 5 m3 / h; Electric motor: 1.2 kW
3.4. Exhaust treatment system
- Wet cyclones: 01 set; Material: stainless steel, load-bearing structure made of steel
- Inlet air temperature: <400 oC; Absorbing solvents: absorb with water + chemicals
- Size: 6000 x 750; Materials: stainless steel, shaped steel
- cushioning materials: ceramic pieces, shells, etc.
- Absorbing solvents: Absorb with water or a chemical solution when needed; Size: 6000 x 1350
- Gas adsorption device: adsorption by activated carbon if needed.
- Materials: stainless steel, load-bearing structure made of steel; Size: 6000 x 1200
- Exhaust fan: 01; Type: industrial fan, stainless steel cover; Electric motor: 15 kW
- Water pump: 01 unit; Type: G7 device (chemical pump); Capacity: 15 m3 / h; Electric motor: 3 kW
- High-pressure misting pumps; 01 item; Type: G7 device; Productivity: 3 m3 / h; Electric motor: 1.5 kW
3.5. Inertial impact treatment tank system
- Size: 5000 x 3500 x 2500 mm
- Material: stainless steel, 4 mm thick
- Size: 25000 x 400
3.7. Electrical equipment
Including control cabinet and related components:
- Control cabinet: automatic control system, PLC; Materials: G7 standards
- Temperature measurement system: Thermocouple, digital display; Measure furnace pressure
- Furnace control; Control water supply; Inverter for exhaust fan; Electrodynamic system
3.8. Air duct system
- Including all kinds of pipes 300, 400 flanges, thu thu, rectangular pipes, rectangular caps, valves of all kinds ....
- The tube made of stainless steel, flanges made of CT3 10-16mm thick.
3.9. Piping system of water intake, valves
Depending on the nature of the water, use steel or plastic pipes.
3.10. Dynamic cable system, control cable, measurement
3.11. Water treatment system
Treatment is up to Class B standard before being discharged into the area's drainage system. Mud pump: 2m3 / h; Acid-resistant waste water pump: 10m3 / h; Chemical magnet pumps; Handling tanks and associated equipment ...
4. Product quality criteria and emissions
- Emissions comply with Vietnam standards TCVN 5937/1995; QCVN 19-24 / 2009 / BTNMT.
Warranty 6 months to 1 year nationwide.